![]() ![]() ![]() The following are some of the examples of valid wildcard masks: ![]() The wildcard mask must meet the following conditions: A zero digit in the wildcard mask indicates that the corresponding hexadecimal digit of the MAC address must be considered and a one digit indicates that the corresponding hexadecimal digit to be ignored. Each digit is a mask for the corresponding hexadecimal digit of the MAC address. The wildcard mask parameter specifies a series of ones and zeroes and has a length of 12 digits. Wild card masks specify which hexadecimal digits of the MAC address are used and which hexadecimal digits are ignored. (Esclusione di responsabilità))Ī wildcard mask parameter has been introduced for extended ACLs and ACL6s and is used with the source MAC address parameter to define a range of MAC addresses to be match against the source MAC address of incoming packets. Questo articolo è stato tradotto automaticamente. (Aviso legal)Įste artigo foi traduzido automaticamente. (Clause de non responsabilité)Įste artículo ha sido traducido automáticamente. (Haftungsausschluss)Ĭe article a été traduit automatiquement. This article has been machine translated.ĭieser Artikel wurde maschinell übersetzt. Questo contenuto è stato tradotto dinamicamente con traduzione automatica. (Aviso legal)Įste texto foi traduzido automaticamente. (Clause de non responsabilité)Įste artículo lo ha traducido una máquina de forma dinámica. (Haftungsausschluss)Ĭet article a été traduit automatiquement de manière dynamique. This content has been machine translated dynamically.ĭieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. Traffic distribution in multiple routes based on five tuples informationīest practices for networking configurationsĬonfigure to source NetScaler FreeBSD data traffic from a SNIP address Using NULL Policy Based Routes to Drop Outgoing Packets Route Health Injection Based on Virtual Server SettingsĬonfiguring a Policy-Based Routes (PBR) for IPv4 TrafficĬonfiguring a Policy-Based Routes (PBR6) for IPv6 Traffic Installing Routes to the NetScaler Routing TableĪdvertisement of SNIP and VIP Routes to Selective AreasĬonfiguring Bidirectional Forwarding Detection NetScaler Support for Microsoft Direct Access Deployment Use Case 3 – Coexistence of Jumbo and Non-Jumbo flows on the Same Set of Interfaces Keeping a VIP Address in the Backup StateĬonfiguring Link Layer Discovery ProtocolĬonfiguring Jumbo Frames Support on a NetScaler Appliance NetScaler Appliances in Active-Active Mode Using VRRPĬonfiguring Health Tracking based on Interface State Monitoring the Bridge Table and Changing the Aging time Monitor the free ports available on a NetScaler appliance for a new back-end connectionĬonfiguring Multiple Untagged VLANs across Multiple SubnetsĬonfiguring Multiple VLANs with 802.1q TaggingĪssociate an IP Subnet with a NetScaler Interface by using VLANs Setting the Timeout for Dynamic ARP Entries So, the interface ID will be 02BB:CCFF:FEDD:1122.Configuring and Managing Virtual IP (VIP) AddressesĬonfiguring ARP response Suppression for Virtual IP addresses (VIPs)Ĭonfiguring GSLB Site IP Addresses (GSLBIP)Ĭonfiguring Prefix-Based IPv6-IPv4 Translation Next, the router will insert FFFE in the middle of the address listed above: This will result in the following hexadecimal address: Well, the router will first flip the seventh bit from 0 to 1. Invert the seventh bit of the interface ID.įor example, if the MAC address of a nework card is 00:BB:CC:DD:11:22, the interface ID would be 02BBCCFFFEDD1122. Insert FFFE in between the two, making the interface ID.ģ. Split the MAC address in two halves (6 hex digits each).Ģ. Here are the rules that a router uses to create the interface ID:ġ. ![]() The interface ID created this way is known as the modified extended unique identifier 64 (EUI-64). Also, the 7th bit in the first byte is flipped to a binary 1. An interface ID is created by inserting the hex number FFFE in the middle of the MAC address of the network card. The second part of an IPv6 unicast address (used to identify a host’s network interface) is usually a 64-bit interface identifier. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |